Anything Goes FALL theme at Paper Players challenge #70

This is very simple card for the Paper Players FALL theme challenge. Here's my card.

It's a very simple card on a natural white card base. It's hard to see in the photo but I started by scoring the two lower corners on opposite angles.

Here is another view, but the one side doesn't want to show up too good.

I really have to work on a light box for photos in the New Year!

I then stamped the top part of the card with French Foliage in more mustard, rich razzleberry and cameo coral. I also used the water spot in river rock. The same was done on the focal piece except everything was stamped off once.

I then heat embossed Give Thanks from the Hand-Penned Holidays in copper embossing powder and matted it with shiny copper paper.

I added a copper leaf brad, then popped it up with a few dimensionals.

The inside is touches of the front but I forgot to take a photo! ddaahhh.

Well that's it.... Done!

It was very difficult to photograph due to the flash back from the shiny copper paper, but I did the best I could. Hope you like it.

Hootie says " Hoot Hoot Hooray...Thanks for stopping by today!"

Please leave a comment with your thoughts; and I hope you will stop by again    

Diane

Watercooler Llama Holiday Hop! Halloween, Thanksgiving & Christmas

This post is for the Watercooler Llama Holiday Hop. If you are following the HOP in order you should have arrived from Debbie Martin's blog. The HOP rules are to make three projects, any holiday of your choice, however, ONE must be a 3D project. .... AND...... It's my very FIRST HOP ever! I'm very excited and nervous all at the same time. Excited to participate but nervous because I don't really understand it all yet and I really hope I linked everything correctly. So with that being said, here are my Watercooler Holiday HOP projects.

PROJECT #1 Halloween Treat Holder

Let's start with Halloween. I made a 3D Witch Hat Candy Holder.

 I used the Petal Cone die and embossed with the Spider Web embossing folder. The base of the hat is a circle cut with my Cricut. I shaded with rich razzleberry ink, added a few strips of  DSP for a band then I tied a rich razzleberry ribbon around the base.

The sentiment from "Hand-Penned Holidays" is stamped and distressed with rich razzleberry ink on piece of whisper white cs with flagged ends. I added to the witch hat with glue dots at the center.

Now for the fun part. When you turn it upside down you find the prize! Two flaps of the Petal Cone die go through two slits in the large circle to form a closure. The other two flap of the die make a easy access to the candy, yet stay closed enough to prevent spillage of the same.

 This photo below shows it closed with a paper clip, but this will be replaced by pieces of magnet sheet. I only hope it holds, otherwise plan 'B' is velcro closings.

Done!

  I hope you like my 3D Witch Hat candy holder. You can find detailed instructions of many demos by typing "petal cone witch hat" into any search engine.

PROJECT #2 Thanksgiving Favor

For my next project I made another 3D table favor for Thanksgiving (or Fall).

 This favor used two cuts from the milk carton die. Here it is ...

Isn't he the cutest little acorn guy ever? I found this punch art acorn from a free tutorial at Stamp and Scrap with Frenchie; check it out! I used dark green cs for the milk carton pieces. Once together I added a strip of DSP as a band and decorated with some leaves stamped from "French Foliage" directly on DSP scraps then fussy cutting them, adding to the box with glue dots.

Here's a peek at the back.

I punch holes around the top flaps and strung with hemp twine and tied a bow.

The little acorn was punched using the ornament punch and a few partial pieces of large and small ovals make the hat and smile. (It's all in the tut). The silver brad was colored with a pumpkin pie write marker. The cheeks come to life with a touch of ink and dauber end, then the eyes are made with a black write marker; hat, cheek and eye highlights from a white gel pen.

"Thanks" from "Fabulous Phrases" was stamped in soft suede on very vanilla and punched with an oval punch, then glued to a piece of cameo coral and punched with the tag punch. It was added with one of the new mini clothespins to the twine! Done!

PROJECT #3 Christmas Card

My third and final project is a Christmas card using the new "Stocking Builder" punch. Here's my card.

It's a pretty simple assembly using lucky limeade cs as a base,then layered with Jolly Holiday DSP (retired and I'm so sad) and I thought this DSP looked like a fireplace. How about you?

I stamped 'believe' in cherry cobbler ink on a piece of very vanilla then drew a line 1/4" inside the edge with a cherry cobbler write marker to connect the sentiment.

I punched two stockings with the Stocking Builder punch from various DSP scraps and assembled, then added some bling with dazzling diamonds. I used a 1/8" hole punch a the top of each stocking,  then tied a bow with cherry cobbler bakers twine. I added to the front with dimensionals. Now we're all ready for SANTA!  Done!

I hope you like my Stocking Builder punch Christmas card. I look forward to any comments on my first HOP attempt.

 I hope you enjoyed viewing my three Watercooler Llama Holiday HOP projects and your next stop on the HOP is Heather!
So to see her fabulous projects just click the box below...


If you would like to return to main page of the  Llama HOP blog click the box below...

SWAP CARD FRONT

For those that did not play this time, here is my SWAP card.

Hootie says " Hoot Hoot Hooray...Thanks for stopping by today!

Please leave a comment with your thoughts; I hope you will stop by again!"

     Diane

Ribbon Loop Christmas {CFC22}

Today's post is for CAS-ual Fridays CFC22  "ribbon loop" challenge.

Here are the particulars.
CFC22: Create a Clean And Simple project using a ribbon tab or loop. Big loops, tiny loops...get creative but the loops on a bow don't count.
Here is my card using two new sets from the Stampin' UP holiday mini; "Christmas Lodge" and "Hand Penned Holidays", and an image from "Bells & Boughs".
 [This is also one of the cards that will be done in my class this week].

The sentiment from "Christmas Lodge" was stamped in crumb cake ink.

The lodge is stamped in brown Stazon on crumb cake cardstock, then the snow is colored with white craft ink and blender pen, then sprinkled with glitter. It's matted on soft suede cardstock, both pieces have the corners punched.

I then rolled the edges inward of a piece of wide striped ribbon, then folded in half and punched a hole with my crop-a-dile. I added to the mat with a large brad. The whole piece was popped up with a few dimensionals.  

Here's a peek at the inside using "Hand Penned Holidays" with that yummy font, and the image from "Bells & Boughs".

I hope you liked my card with a LOOP!

Hootie says " Hoot Hoot Hooray...Thanks for stopping by today!

Please leave a comment with your thoughts; I hope you will stop by again!"

Diane